h i gh voltage fast recovery rectifiers m a x i m u m r atings and electrical characteristics rating 25 c ambient temperature uniess otherwies specified. s ingle phase half wave, 60hz, resistive or inductive load. for capacitive load, derate current by 20%. type number m aximum recurrent peak reverse voltage m aximum rms voltage m aximum dc blocking voltage m aximum average forward rectified current .375"(9.5mm) lead length at ta=50 c features m e chanical data p eak forward surge current, 8.3 ms single half sine-wave s uperimposed on rated load (jedec method) m aximum instantaneous forward voltage at 0.5a/0.2a d.c. m aximum dc reverse current ta=25 c at rated dc blocking voltage ta=100 c 50 0 200 30 5.0 100 500 m a a v m a m a * low forward voltage drop * high current capability * high reliability * high surge current capability * case: molded plastic * epoxy: ul 94v-0 rate flame retardant * lead: axial leads, solderable per mil-std-202, method 208 guranteed * polarity: color band denotes cathode end * mounting position: any w eight: 0. 40 grams r1 5 0 0 f r 4 0 0 0 f thru 2. 0 4. 5 * v oltage range 1 5 00 to 40 00 v olts current 500 & 200 m ampere v R1500F r1600f r1800f r2000f r2500f r 40 00 f units 1 500 1600 1800 2000 2500 40 00 1500 1600 1800 2000 2500 4000 1050 1 120 1260 1400 1750 28 00 v v m aximum reverse recovery time (note 1) typical junction capacitance (note 2) 40 - 65 +175 ns pf notes: 1. reverse recovery time test condition: if=0.5a, ir=1.0a, irr=0.25a 2. measured at 1mhz and applied reverse voltage of 4.0v d.c. operating and storage temperature range t , t j s tg c 258 dimensions in inches and (millimeters) do-15 1.0(25.4) min. 1.0(25.4) min. .300(7.6) .230(5.8) .03 1 (. 8 ) .02 3 (. 6 ) dia. .140(3.6) .104(2.6) dia.
.1 1.0 10 100 r a ting and characteristic cu r ves (r 15 00f thru r 40 00f) fig.1 - typical reverse characteristics reverse leakage current, ( a) m percentage rated peak reverse voltage 0 20 40 60 80 100 120 140 .01 fig.2-typical forward current derating curve average forward current,(ma) tj=100 c tj=25 c 100 0 200 300 400 500 600 0 20 40 60 80 100 120 140 160 180 200 ambient temperature ( c) single phase half wave 60hz resistive or inductive load 0.375"(9.5mm) lead length fig.5-typical junction capacitance reverse voltage,(v) j unction capacitance,(pf) 140 120 100 80 60 40 20 0 .01 .05 .1 .5 1 5 10 50 100 r 1 5 0 0 f ~ r 1 8 0 0 f r 2 0 0 0 f ~ r 4 0 00 f ( + ) ( + ) 25vdc ( approx.) ( ) ( ) pulse generator (note 2) oscilliscope (note 1) 1 non- inductive w notes: 1. rise time= 7ns max., input impedance= 1 megohm.22pf. 2. rise time= 10ns max., source impedance= 50 ohms. + 0.5a 0 - 0.25a - 1.0a | | | | | | | | 1cm set time base for 50 / 10ns / cm trr d.u.t. fig.3- test circuit diagram and reverse recovery time characteristics 10 noninductive 50 noninductive w w fig.4-maximum non-repetitive forward surge current 6 0 12 18 24 30 number of cycles at 60hz 1 10 5 50 100 tj=25 c 8.3ms single half sine wave jedec method peak forward surge current,(a) 259
|